Designed for Naturally Aspirated Applications
Compatible with Honda/Acura B Series Engines
Aluminum Construction
Includes All Necessary Mounting and Installation Hardware

Description
Vehicle Fitment
Technical Data
Included

Discontinued - 4/30/2026

SpeedFactory Naturally Aspirated Catch Can - Honda/Acura B Series Engines

Your factory PCV system recirculates crankcase blow-by back into your intake, which means oil vapors are going back into your engine and coating your intake manifold, throttle body, and valves with oil residue. A catch can intercepts that blow-by and traps the oil and moisture before it gets back into your intake. The SpeedFactory naturally aspirated catch can replaces your factory PCV system with a clean breather setup that vents crankcase vapors through a filter instead of recirculating them. It's designed specifically for B series naturally aspirated engines but it can be adapted to other applications too.

Why You Need a Catch Can

Every engine produces crankcase blow-by. That's combustion gases and oil vapor that slip past your piston rings and end up in the crankcase. Your factory PCV system sucks that vapor back into the intake to be burned, but it also pulls oil along with it. Over time, your intake manifold and valves get coated in an oily film that hurts airflow and fuel atomization. A catch can traps the oil and moisture before it recirculates, keeping your intake cleaner and your engine running better.

Designed for B Series Naturally Aspirated Engines

This catch can is designed for naturally aspirated B series engines (B16, B17, B18, B20) that aren't turbocharged or supercharged. The kit includes B series specific adapter fittings that bolt directly to your engine block breather ports. If you're running a turbo or supercharger, you need a different catch can setup designed for forced induction applications.

Replaces the Factory PCV System

This setup removes the factory PCV valve and replaces it with the catch can. Oil vapors and blow-by get routed through the catch can where the oil and moisture condense and collect in the can. The remaining vapors vent to the atmosphere through the included breather filter. You drain the collected oil out of the can periodically using the drain plug at the bottom.

Complete Kit with All Hardware

SpeedFactory includes everything you need to install this catch can on your B series engine. You're not sourcing hose fittings, clamps, or mounting hardware separately. Just bolt it up and route the hose.

What You Get
- Naturally aspirated catch can (3 inch diameter x 7 inch tall)
- Breather filter
- Two B series engine block adapter fittings
- Two catch can hose fittings (1/2 inch NPT x 1/2 inch barbed)
- Mounting bracket and clamp
- Drain plug
- 1/2 inch oil hose and four clamps
Specifications
- Catch can diameter: 3 inches
- Catch can height: 7 inches
- Hose size: 1/2 inch
- For naturally aspirated engines only (non-turbocharged, non-supercharged)
Designed For
- B16A
- B17A
- B18A/B
- B18C1
- B18C5
- B20B/Z
- Other naturally aspirated applications with similar breather port sizing
Important: This catch can is for naturally aspirated engines only. Do not use it on turbocharged or supercharged setups. Drain the collected oil from the catch can periodically. Check the can during oil changes and drain as needed.
1990-2001 Acura Integra
1999-2000 Honda Civic Si

1997-2001 Honda CR-V

1994-1997 Honda Del Sol VTEC
Catch can diameter: 3 inches
Catch can height: 7 inches
Hose size: 1/2 inch
(1) Oil Catch Can
(1) Vent Filter

(1) Mounting Bracket (Not Pictured)

(2) Brass Barb Fittings - 1/2" NPT x 1/2"

(2) B Series Engine Block Adapter Fittings

(1) Reel of Hose

(4) Small Worm Gear Clamps

(1) T Bolt Clamp

(1) Drain Plug

Catch Cans

Verus Engineering Air Oil Separator for 17-21 Civic Type R

Mishimoto Oil Catch Can (FK8/FL5 Civic Type R)

SpeedFactory 3-Filter Oil Catch Can for Civic/Integra

SpeedFactory Naturally Aspirated Oil Catch Can for B Series